12 visiting now: 5 USA USA flag 4 Germany Germany flag 1 France France flag 1 Spain Spain flag 1 Ukraine Ukraine flag

Highlighted Companies



Fogging Tester - China

price: 1.00 Dollar US$

Brief Introduction:
The fogging tester is designed to test the fogging phenomena of leather and fabric under specified environment conditions, suitable for the fogging property evaluation of volatile components of the interior trimming materials used in cars and aircrafts under high temperature, and the instrument can also be used to test the fogging property of car xenon lamps. Working Principle:
The main frame of the tester includes a water sink fully filled with specified ethylene glycol, which can reach a high temperature. At the time of testing, leather specimens are put in the six standard glass containers filled with high temperature liquid, and the stainless steel containers are placed above each glass. Relying on the constant water flow distribution, the temperature can maintain at 20℃ constantly, and it can be adjusted through the regulation device connected to the main frame. This controlled environment condition will generate a layer of “fog” on the surface of specimens. The operator can determine the fogging characteristics of materials based on gravimetric analysis method or refraction method. Test Methods:
It applies to the following test methods:
1) Gloss Method: the sample cup is heated by the fog evaporated gas condensing on cold glass by glass gloss values were compared before and after condensation and calculated, the sample can be drawn into the fog value.
2) Gravimetric method: the sample cup is heated by the fog evaporated gas condensing on cold aluminum foil, aluminum foil condensed by weighing before and after the change in weight, the sample can be drawn from the atomization - the weight of condensate.
3) Haze method: the sample cup is heated by the fog evaporated gas condensing on cold glass, through the haze value before and after the glass condensate compare and calculate, the sample can be drawn into the fog value. Standards
DIN 75201 Determination of the fogging characteristics of trim materials in the interior of automobiles
ISO 6452 Rubber or plastics coated fabrics-determination of fogging characteristics of trim materials
in the interior of automobiles
SAE J1756 Test procedure to determine the fogging characteristics of interior automotive materials
QB/T 2728 Leather-physical and mechanical test-determination of fogging characteristics.
BS EN 14288 Leather - Physical and mechanical tests - Determination of fogging characteristics
PV 3920 Determination of fog value (F) of non-metallic interior materials
PV 3015 Non-metallic materials for interior trim-determination of condensable constituents.
ES-X83231 Standard test method-For fogging of interior materials
NES M0161 Interior materials fog test method
D45 1727 TRIM MATERIALS AND PARTS FOR INTERIOR AND PASSENGER COMPARTMENT PARTS - FOGGING - CONDENSATION
GM 9305P Determination of fogging characteristics of automotive interior trim materials
TSM 0503G Fogging test method for non-metallic materials Features:
CONSTRUCTIVE CHARACTERISTICS:
· Internal carrying plane, in structural treated steel, anti-acid painted.
· External protection in sheet steel of proper thickness, anti-acid treated and painted with epoxy resin.
· six work places 18/8 Inox steel test room. · 18/8 Inox steel lift able cooling system. · Rapid clutch Agitation System. · Armored resistances. · Security thermostat. · Cooling liquid and relief entry etching with rubber-carrier. SECURITY NORMS: · Safety Magnetic Switch. · Digital thermos regulator and microprocessor. · Electronic auto programmable timer · START-STOP switches, · Warning Lamps. · End test buzzer hint signal Technical Parameter:
Hot bath temperature range: room temperature ~ 150 ℃ (room temperature ~ 280 ℃ optional)
High-temperature tank temperature control accuracy: ± 0.1 ℃ (150 ℃)
Low bath temperature range: 0 ~ 100 ℃
Cold tank temperature control accuracy: ± 0.1 ℃
High temperature trough Dimensions: 670 mm (L) × 490 mm (B) × 540 mm (H)
Cryogenic tank Dimensions: 400 mm (L) × 220 mm (B) × 520 mm (H)
Temperature tank Weight: 32kg (not including the thermally conductive medium)
Cryogenic tank Weight: 15kg (not including the thermally conductive medium)
Power: AC 220V 50Hz
Weight: 50kg
Size: 500 * 650 * 600mm
Temperature stability: ± 0.1 ° C (200 ° C)
Heating power: 3KW
Cooling capacity: 500W
Data communication: multi-function remote sensor and USB port
Safety magnetic switch
Warning Light
Test completion tips Consumables:
Glass (square, circle);
Test plate frame;
Nebulizer cup;
Sampler;
Aluminum foil;
Filter paper;
Rubber ring 95 * 4;
DOP;
DIDP;
Silicone oil; Test accessories:
Cooling plate * 6
Flat heat resistant glass beaker * 6
Chrome steel ring * 6
Fluorine rubber seals * 6
Seal ring * 6
Square glass plate * 6 (Reflective test)
Glass plate frame
Aluminum foil
Aluminum foil sampler
Aluminum foil sealed round glass plate * 6
Dioctyl phthalate (DOP) * 1
Diisodecyl phthalate (DIDP) * 1
Φ80mm sampler
Oven
Electronic balance (0.01mg)
Gloss meter
Haze meter


Company Contact:


  • Phone: +862164200566

  • Address: No. 2578 Minhang District Gu Dai Road, Shanghai, Shanghai, shanghai, China

  • Email: Email


Published date: January 4, 2018 -

  • Business Description: Qinsun Instruments Co., Ltd was founded in 2010, comprised of many experienced engineers and designers standing in the forefront of the industry.

Related listings



  • Jis Rubbing Colour Fastness Tester
    Jis Rubbing Colour Fastness Tester
    Electrical equipment and components - Qinsun Instruments (Shanghai) Co., Ltd. - China - January 4, 2018 - 1.00 Dollar US$

    This rubbing color fastness tester is a standard testing machine of the Type II rubbing tester (GAKUSIN TYPE) specified in JIS L0849 Test Method of Rubbing Fastness in JIS Textile-Tests For Color Fastness. It is applied to determine the color resista...

  • American Standard Whirlpool Shrinkage Dryer
    American Standard Whirlpool Shrinkage Dryer
    Electrical equipment and components - Qinsun Instruments (Shanghai) Co., Ltd. - China - January 4, 2018 - 1.00 Dollar US$

    Brief Introduction Whirlpool 3LWED4900YW - American Association of Textile Chemists and dyeing of Jurists (AATCC) approved standard shrinkage test (special) brand dryers. Testing of textiles after one or more times after washing, obtain shrinkage or ...

  • Ozone Aging Color Fastness Tester
    Ozone Aging Color Fastness Tester
    Electrical equipment and components - Qinsun Instruments (Shanghai) Co., Ltd. - China - January 4, 2018 - 1.00 Dollar US$

    Brief Introduction The textile ozen aging color fastness tester is mainly used for testing color fastness properties of fabrics exposed to ozone environment; it is the special equipment for testing the fabric colorfastness to ozone. Product Descripti...



Safe Trade Tips

  • Ask for business references and check them
  • Use a payment method that offers better protection for all such as Letters of credit and verified professional escrow services. Avoid payments in advance such as money transfers
  • Verify their business via their local Chamber of Commerce
  • Search the internet using their website address, their business name, their phone and fax numbers, and their email addresses to see if you can find any feedback about them.
  • Get to know more about scams to avoid: Internet Crime Complaint Center - International Financial Scams
  • This site is never involved in any transaction, and does not handle payments, shipping, guarantee transactions, provide escrow services, or offer "buyer protection" or "seller certification"