Pbg Shield Type Hot Water Circulation Booster Pump - Chinaprice: 100.00 Dollar US$
PBG Shield type hot water circulating booster pump This pump is suitable for below 100 ℃ hot and cold-water circulation and pressurization/booster, especially for the shower due to low water pressure, pressurization for Low household water pressure and water supply, water supply for solar water heater, hot water circulation pressurization for boiler, liquid booster and circulation for industrial equipment, circulation and pressurization for air conditioning and refrigeration systems.
The structure of pump adopts stainless steel sleeve to make the iron core of motor and the water completely be shielded for isolation and cancel the traditional mechanical seal.
It can solve the problem of the conventional water seal leakage.
bearing, ceramic shaft, wear-resisting, anti-corrosive, natural water lubrication, low noise, working voltage does not load all the way, as long as the correct use, long service life, All the materials inside the motor are made of high temperature and high-quality materials.
It suitable for hot water cycle pressurization system, pump can be equipped with automatic water control switch.
More convenient to use.
The pump wire box is designed with three-speed switch.
It can be adjusted according to different environment and requirements of users.
working conditions 1, the transmission medium temperature range: 0℃-100℃ 2, the highest ambient temperature: +40℃ 3, medium requirements: clean liquids.
No solid debris, no viscosity, no corrosion
4, chemical properties: neutral, non-explosive liquid similar to water (glycol content 30%) 5 - To extract other liquids, consult the manufacturer first 6, the maximum working pressure 100PA 7, minimum inlet pressure: temperature at 50℃ at 0.05bar The temperature is 95 ℃ at 0.3 bar The temperature is 110 ℃ at 1.0 bar The above values are only suitable for increasing 0.01bar at 100m at an altitude of 300m, and the maximum inlet pressure should be maintained to prevent noise caused by cavitation.
8, rated voltage between -10% to 10%, When too low voltage will appear particularly slow, the pump cannot start or heating fast, resulting in not enough head pressure.
- Phone: +8651258583352
- Address: Room 216-108, Textile resources market, Zhangjiagang , SUZHOU , China
- Website: http://www.kenshine-pump.com
Published date: October 6, 2021
- Business Description: Our company is specialized in water pumps, electromechanical equipments and accessories etc for many years:
…Various fluid pumps(centrifugal pump, chemical industrial pump, submersible pump, self priming pump, sewage pump, electromagnetic pump, diaphragm pump, gear pump, screw pump etc and their parts such as mechanical seal, pump casings, coupling, impellers etc)
…Oil drilling equipments and parts (triplex mud pump, mud valve, drilling motor, drilling bits and parts of mud pumps such as piston, cylinder, valves and seats etc)
…Mechanical parts and tools, instruments etc
Tobee® E4041hs1 Slurry Pump Frame Plate Liner Insert Is A Hi Seal PartIndustrial pumps and compressors - Hebei Tobee Pump Co.,Limited - China - September 30, 2021 - 3000.00 Dollar US$
E4041HS1 slurry pump frame plate liner insert is a hi-seal slurry pump parts used on 6x4 DAH Slurry Pump and 6x4 EAH Slurry Pump. Slurry Pump Frame Plate Liner Insert is a wear part of slurry pumps, It is also called for slurry pump back liner based ...
Tobee® E4110 A05 Slurry Pump Volute Liner Is An Important Wear PartIndustrial pumps and compressors - Hebei Tobee Pump Co.,Limited - China - September 30, 2021 - 3000.00 Dollar US$
Tobee® E4110-A05 Slurry Pump Volute Liner is an important wear part of 6/4D-AH & 6/4E-AH slurry pumps. It forms a slurry pump chamber with a throat bush and frame plate liner insert where the slurry would flow through them. Slurry volute Liner is...
Tobee® Sp65191 A05a Impeller Is One Of The Wetted Spares For Sp65qv Vertical Slurry PumpIndustrial pumps and compressors - Hebei Tobee Pump Co.,Limited - China - September 30, 2021 - 3000.00 Dollar US$
Tobee® SP65191-A05A Impeller is one of the wetted spares for SP65QV Vertical Slurry Pump, this Slurry Pump Impeller is a kind of semi-open impeller. Tobee's high chrome wear parts provide users with longer 30%-60% wear life and higher efficiency due ...
Safe Trade Tips
- Ask for business references and check them
- Use a payment method that offers better protection for all such as Letters of credit and verified professional escrow services. Avoid payments in advance such as money transfers
- Verify their business via their local Chamber of Commerce
- Search the internet using their website address, their business name, their phone and fax numbers, and their email addresses to see if you can find any feedback about them.
- Get to know more about scams to avoid: Internet Crime Complaint Center - International Financial Scams
- This site is never involved in any transaction, and does not handle payments, shipping, guarantee transactions, provide escrow services, or offer "buyer protection" or "seller certification"